Showing results: 226 - 240 of 426 items found.
-
Wuxi IMHOO Technology Co., Ltd.
1)For monitoring the ON/RUN time of AC2)Powered equipment3)Suitable for usage of hourse , factory , etc .4)Time setting from 0 to 99999.99 hours ( 5+2digits ) 5)With back cover6)Input voltage source: Ac 110/220/380V 50-60Hz7) Power consuption: 2.5W8) Mounting : by nuts , or DIN rail 9)Size/weight:70X70X50mm/480g
-
PCIEXT-64UB - Live Insertion PCI Bus Extender -
Ultraview Corporation
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
PCIEXT-64 - Live Insertion PCI Bus Extender -
Ultraview Corporation
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
PCIEXT-64U - Live Insertion PCI Bus Extender -
Ultraview Corporation
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
FR-103HP -
Femtochrome Research, Inc.
The FR-103HP is a compact NL crystal autocorrelator, suitable for moderate and high power lasers (Pav>5mW). It is available with a scan range >60ps (suitable for pulsewidths within 10fs-15ps) and covers a wide range of wavelengths with easily interchangeable plug-in detector modules. The standard FR-103HP provides ‘real-time’ pulsewidth monitoring capability for rep rates down to 1kHz.
-
OP-SB84 -
LINEEYE Co., Ltd.
OP-SB84 is an expansion board for monitoring USB2.0 and measuring VBUS power, inserting into a slot of portable communication analyzer (LE-8200A/LE-8200). It is a stand-alone USB analyzer, exchanging the measurement board and line state sheet for USB signals. This equipment runs without a PC and useful not only for developing USB devices but also trouble shooting and after-supporting of USB devices.
-
Datum Electronics, Ltd.
We also offer rotary power sensors, rotary torque sensors and torque meters that are capable of measurements above our standard range of 20,000NM to meet the needs of our customers within a commercial environment.Our standard torque sensor range incorporates the measurement of torque up to 60,000Nm, these provide solutions to most test and monitoring requirements.
-
PERCEPTION COMMANDER -
GE Digital Energy
PERCEPTION COMMANDER is an Advanced Transformer Asset Management software platform developed to address the changing needs of the modern day utility and power transformer user. PERCEPTION COMMANDER allows both the Maintenance Engineer and Asset Manager to monitor and diagnose the DGA data collected from their on-line monitoring units and determine the condition of their transformer network in one program.
-
EP600i -
CANDURA Instruments
The EnergyPro EP600i is portable and easy to use. Perfect for single phase or three phase energy consumption analysis and basic power quality monitoring. It supports standard wiring configurations and comes with a set of 1A - 2500A WideRangeFlexCT ™. The graphics display makes setup very easy and intuitive - you can setup and record data without looking at the manual!
-
STMicroelectronics
ST is a world-class supplier of IC smart power solutions for all the Chassis and Safety applications, ranging from passive safety, braking, vehicle dynamics and steering systems. Type of devices in ST portfolio are analog and mixed-signal ICs, integrating different functions such as supply modules, drivers for loads and actuators, diagnostic functions, system monitoring and communication interfaces.
-
VME8200 -
CAEN S.p.A.
The power supply is placed in the bottom, behind the fan tray unit, in order to keep the rear of the VME backplane completely accessible. Safety features include: short circuit protection, Over / Under voltage protection, Over temperature protection. Remote monitoring and control take place through CAN bus, Ethernet, USB and RS232 interfaces.
-
MC-2RD -
Semapi Corp
The MC-2RD is the newest and low-cost vibration measurement solution for On-line monitoring of critical rotating machinery.This monitor controls the vibration levels of any kind of rotating machinery, no matter its power, protecting the machinery from any vibration variation.The module MC-2RD is easy to install because of it´s housing in an electrical panel just by a Din rail.
-
Whistler
1200 Watts Continuous - 2400 Watts Peak Power3 AC Outlets - 2 USB Ports for powering/charging devices such as game systems, laptops, and moreDigital Volt/Watt Meter for monitoring power usageThermostat Controlled Fan and Overload IndicatorElectronic Circuit Protection which includes: Smart Surge Control, Overload/Voltage Protection, Short Circuit Protection, and Thermal Cutoff
-
ACSRF-4040 -
Gemini Data Loggers Ltd.
The Plus Radio Ethernet receiver is required as part of the Tinytag Radio Data Logging System. It controls the transmission of data to and from the radio loggers: data received from the loggers is then sent to the computer for viewing with Tinytag Explorer radio software. If power to the computer running the system is lost, the receiver has a battery back-up which will maintain the mesh network until power is restored. This receiver plugs directly into a LAN removing the need for a computer in the area where monitoring is to take place. The receiver is powered using a plug-in Power over Ethernet adaptor (ACS-0041) which is supplied with the unit.
-
MOS-01, -01A -
Compact Power Company
The MOS-01 manual oscillator module is used as a quality, general-purpose sinewave oscillator and digital readout monitoring system in the MAC-01, -02, or -03 AC Power Sources/Frequency Converters. The unit has guaranteed operating range of 20 HZ to 20 KHZ which is covered in three one-decade scales. The LCD digital metering system is switch-selectable to readout either frequency, voltage or current. A toggle switch selects the input for the attached AC Power Source/Frequency Converter to originate from the manual oscillator itself or from an external laboratory or programmable oscillator source. With oscillator mode switch in Internal position, the BNC connector delivers the signal to drive additional slave units or for oscilloscope sync or monitoring. BNC input/output is completely isolated with 1500 VAC breakdown and excellent common mode rejection. The oscillator modules must be factory installed and calibrated.